TUA - Thermostatic Expansion Valves for Ice Machines
These kits are designed with contractors in mind to help save time and money by providing a universal valve that can easily be adapted to
replace most OEM specic TXVs. Two kits are available, each with a valve body and a selection of three orice sizes, copper ttings (two elbows
and one reducer), a patented bulb strap, and insulation tape.

680 Series
Enhance the performance and safety of your HVAC system with the Robertshaw® Goodman Direct Replacement Flame Sensor with a Straight Rod.

Designed as an exact match for Goodman's 0130F00010S.

Will fit in a variety of Goodman and Amana Furnace series, ADV, AMV, CPG, DBG, DC80, DC96, DCG, DD80, DFG, DK92, DM80, DM92S, DM96, DRG, DSG, GC9, GCE, GCH, GM9, GME, GMS, GMV, GPD, GPG.

The Robertshaw® aluminum tubing is versatile for all your replacement needs. It comes in a full range of sizes in 50 foot and 5 foot lengths.

Features and Benefits

Aluminum tubing meets ASTMB Standard #483
Uses a 1435 alloy with a 0.035" wall thickness
Tubing is rated at 90 PSI with an 11,000 tensile, 9500 yield and a 25% elongation

The Robertshaw® aluminum tubing is versatile for all your replacement needs. It comes in a full range of sizes in 50 foot and 5 foot lengths.

Features and Benefits

Aluminum tubing meets ASTMB Standard #483
Uses a 1435 alloy with a 0.035" wall thickness
Tubing is rated at 90 PSI with an 11,000 tensile, 9500 yield and a 25% elongation

Universal flat silicon carbide igniter kit. Includes brackets and hardware to replace hundreds of OEM furnace and boiler igniters

SENSOR, FLAME, SILICON CRBD, 1800°F, 3100°F

18 ga copper high temperature fiberglass insulated lead wires
Faster time to temperature response, higher resistance to oxidation
Longer usable life, lower power consumption, more robust in transit, stronger more durable design
Supco flat igniters offer an efficient , stronger, reliable hot surface silicon carbide design, superior gas lighting ability

Seal kit (NC); O-ring for armature tube, rubber gasket, O-ring for steel cover, support ring

AEROSOL COIL CLEANER
Viper is a potent degreasing compound that does not contain any hazardous ingredients or give off toxic fumes. Use it to clean small indoor kitchen equipment, condenser and evaporator coils. No need to rinse the evaporator and the condenser only needs a light water rinse for minimal clean-up. The aerosol injector produces a pin spray of expanding foam that penetrates deep in between the coil fins. The foam will liquefy after a few minutes removing heavily imbedded grease and grime.

Non-Rinsing Formula
Non-Toxic
No Odors
Use on Condensers and Evaporators

PURE CONCENTRATE COIL CLEANER
Venom Pack All-Purpose is your go to cleaner for just about anything. This product washes away bacteria, stubborn soils, heavily imbedded cooking greases, and is extremely effective on everyday dirty surfaces. Use it in the shop, in the field, or at home. Our All-Purpose cleaner is non- toxic, eco-friendly and NSF approved for use on food equipment. Safe for all metals including aluminum.

Spray and Wipe formula
Washes away bacteria
Safe on all materials
Lightweight pure concentrate

Dramatically reduces the time to make flares and has a tool used with a cordless drill for the fastest flaring.

Seal kit (NC); (4) O-rings, (2) Al. gaskets

MaterialAluminum, Zinc coated steel ConstructionOne-piece; hubbed, hubless, or unit-bearing

UNIVERSAL FOAM GUN TIPS
These universal tips fit most models of Foam Sprayers including the RT300S Viper Foam Sprayer. Simply remove and replace broken or lost tips with ease.

Universal Tip Replacements
Fits most models of Foam Sprayers
2 Tips Per Pack
Easily Stored in a Reusable Clamshell

¼" Male Flare X ⅛" MPT Elbow w/ Wrench Cap & Core

Features/Benefits

¼" SAE Male Flare
⅛" MPT
Brass cap with Neoprene O-ring
Stainless steel valve core, suitable for all refrigerants

The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.

Arched top, concave sidewalls and rounded corners provide uniform tensile loading and uniform pulley sidewall contact for excellent belt service life and reduced pulley wear.

Vulcanized Flex-bonded tensile cords provide superior resistance to tensile and flexing forces, fatigue and shock loads.

Flex-Weave™ oil and heat resistant cover protects the belt core from the toughest environments.

All sizes meet Gates V80™ system matching tolerances.

Meets ARPM/RMA IP-3-2 oil and heat resistant standards and IP-3-3 static conductivity requirements. REACH and RoHS 2 compliant.

The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.

Arched top, concave sidewalls and rounded corners provide uniform tensile loading and uniform pulley sidewall contact for excellent belt service life and reduced pulley wear.

Vulcanized Flex-bonded tensile cords provide superior resistance to tensile and flexing forces, fatigue and shock loads.

Flex-Weave™ oil and heat resistant cover protects the belt core from the toughest environments.

All sizes meet Gates V80™ system matching tolerances.

Meets ARPM/RMA IP-3-2 oil and heat resistant standards and IP-3-3 static conductivity requirements. REACH and RoHS 2 compliant.

Cartridge Bearing; 1" Bore; 2-17/32" Outside Diameter; 1" Cartridge Housing Width; Concentric Collar; Cartridge Unit Housing; Rubber; Ball Bearing; 1.43" Length Thru Bore; Not Relubricatable; SLRB-116 Insert; Single Lip Contact Seal; Non-Expansion

The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.

Arched top, concave sidewalls and rounded corners provide uniform tensile loading and uniform pulley sidewall contact for excellent belt service life and reduced pulley wear.

Vulcanized Flex-bonded tensile cords provide superior resistance to tensile and flexing forces, fatigue and shock loads.

Flex-Weave™ oil and heat resistant cover protects the belt core from the toughest environments.

All sizes meet Gates V80™ system matching tolerances.

Meets ARPM/RMA IP-3-2 oil and heat resistant standards and IP-3-3 static conductivity requirements. REACH and RoHS 2 compliant.

The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.

Arched top, concave sidewalls and rounded corners provide uniform tensile loading and uniform pulley sidewall contact for excellent belt service life and reduced pulley wear.

Vulcanized Flex-bonded tensile cords provide superior resistance to tensile and flexing forces, fatigue and shock loads.

Flex-Weave™ oil and heat resistant cover protects the belt core from the toughest environments.

All sizes meet Gates V80™ system matching tolerances.

Meets ARPM/RMA IP-3-2 oil and heat resistant standards and IP-3-3 static conductivity requirements. REACH and RoHS 2 compliant.

MaterialAluminum, Zinc coated steel ConstructionOne-piece; hubbed, hubless, or unit-bearing

Vibration absorbers are designed for installation in the suction and discharge lines of air conditioning, heat pump and refrigeration systems to dampen the transmission of compressor induced vibration through the system piping.

Features/Benefits

100 % helium and hydrogen leak tested
Compatible with all refrigerants
Deep pitch stainless steel hose and high tensile wire braid
Unique proven design for high pressure applications rated for R410A

Vibration absorbers are designed for installation in the suction and discharge lines of air conditioning, heat pump and refrigeration systems to dampen the transmission of compressor induced vibration through the system piping.

Features/Benefits

100 % helium and hydrogen leak tested
Compatible with all refrigerants
Deep pitch stainless steel hose and high tensile wire braid
Unique proven design for high pressure applications rated for R410A

MaterialAluminum, Zinc coated steel ConstructionOne-piece; hubbed, hubless, or unit-bearing

Vibration absorbers are designed for installation in the suction and discharge lines of air conditioning, heat pump and refrigeration systems to dampen the transmission of compressor induced vibration through the system piping.

Features/Benefits

100 % helium and hydrogen leak tested
Compatible with all refrigerants
Deep pitch stainless steel hose and high tensile wire braid
Unique proven design for high pressure applications rated for R410A

The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.

Arched top, concave sidewalls and rounded corners provide uniform tensile loading and uniform pulley sidewall contact for excellent belt service life and reduced pulley wear.

Vulcanized Flex-bonded tensile cords provide superior resistance to tensile and flexing forces, fatigue and shock loads.

Flex-Weave™ oil and heat resistant cover protects the belt core from the toughest environments.

All sizes meet Gates V80™ system matching tolerances.

Meets ARPM/RMA IP-3-2 oil and heat resistant standards and IP-3-3 static conductivity requirements. REACH and RoHS 2 compliant.

MaterialAluminum, Zinc coated steel ConstructionOne-piece; hubbed, hubless, or unit-bearing

Vibration absorbers are designed for installation in the suction and discharge lines of air conditioning, heat pump and refrigeration systems to dampen the transmission of compressor induced vibration through the system piping.

Features/Benefits

100 % helium and hydrogen leak tested
Compatible with all refrigerants
Deep pitch stainless steel hose and high tensile wire braid
Unique proven design for high pressure applications rated for R410A

The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.

Arched top, concave sidewalls and rounded corners provide uniform tensile loading and uniform pulley sidewall contact for excellent belt service life and reduced pulley wear.

Vulcanized Flex-bonded tensile cords provide superior resistance to tensile and flexing forces, fatigue and shock loads.

Flex-Weave™ oil and heat resistant cover protects the belt core from the toughest environments.

All sizes meet Gates V80™ system matching tolerances.

Meets ARPM/RMA IP-3-2 oil and heat resistant standards and IP-3-3 static conductivity requirements. REACH and RoHS 2 compliant.

The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.

Arched top, concave sidewalls and rounded corners provide uniform tensile loading and uniform pulley sidewall contact for excellent belt service life and reduced pulley wear.

Vulcanized Flex-bonded tensile cords provide superior resistance to tensile and flexing forces, fatigue and shock loads.

Flex-Weave™ oil and heat resistant cover protects the belt core from the toughest environments.

All sizes meet Gates V80™ system matching tolerances.

Meets ARPM/RMA IP-3-2 oil and heat resistant standards and IP-3-3 static conductivity requirements. REACH and RoHS 2 compliant.