EVR Version 2 - Solenoid Valves
EVR Version 2 solenoid valves are direct or servo-operated solenoid valves for liquid, suction, and hot gas lines. They are suitable for all
refrigeration, freezing, and air conditioning applications and are compatible with fuorinated refrigerants. The valves can be delivered as
normally open or closed as well as with or without manual operation.

Sil-Fos 5 is a silver-copper-phosphorus alloy for copper-copper brazing but can also be used to join brass with an appropriate flux (e.g. Handy Flux, Ultra Flux). It is a more cost effective Ag-Cu-P alloy, though it does not penetrate deep joints easily.
Joins CU to CU (phosphorus serves as flux)
Joins CU to Brass (flux is recommended)
Lower cost alternative to higher silver content Ag-Cu-P alloys
Medium flow
Made in USA
Industry Applications:
HVAC/R refrigerant systems, air conditioning coils, evaporator coils

KPU - Pressure Switches
KPU pressure switches are designed to be contractor friendly and used in refrigeration and air-conditioning systems to protect the systems
from excessively low suction or high discharge pressure. They can also be applied to start and stop compressors and the fans of air-cooled
condensers. KPU pressure switches, in single and dual versions, cover a comprehensive range of applications and are designed for use with
Fluorinated and non-aggressive refrigerants. Most KPU pressure controls can be used with R-410a systems with only a few code numbers.

ALL PURPOSE WIPES
Viper Wipes are an ultra-strong dual textured hand towels that will clean almost anything. Use to remove dirt, grease, oil, grime, tar, mastic, caulking and more! Towels absorb soils leaving your hands clean. These convenient wipe and go towels are used by professional mechanics on the road, on the roof and in the shop. No water rinse is required. Viper Wipes contain Lanolin, Aloe, and Vitamin E for soothing relief on hands covered with nicks, scraps, and minor cuts.

Waterless Hand Wipes
Cleans Tools and Equipment
Removes Tough Grease and Mastic
Leaves Hands Smooth and Soft

HEAT BLOCKING GEL
Viper Heat Blocking Gel is used to prevent fire or heat damage when using an open flame around wood, drywall, fabric and other components. It can also be used as a heat dissipating gel when protecting sensitive components in low temperature soldering applications. For high temperature brazing, soldering or welding we recommend our Viper Heat Blocking Putty.

Prevents Fires
Protects Sensitive Components
Wipes off easily
Non-Toxic and No Odors

GASKET & THREAD SEALANT
Nylog Blue is an elastic fluid made from synthetic refrigeration grade compressor oil. Nylog Blue is fully miscible and compatible with all system refrigerants and oils. Gaskets coated with Nylog will never dry or become heat fixed to the surface. Threaded connections coated with Nylog will block high pressure leaks by forming a hydraulic seal. Nylog can be used an assembly lube when installing shaft seals, o-rings, schraeder valves, ball valves, or other internal system components.

The HT-VCL-30P 115 Volt high-temperature condensate removal pump with 1-gallon collection tank is designed for plenum applications with the capability to handle the most difficult commercial applications.

These black disposable Grease Monkey gloves protect hands for brief exposure periods. They are powder-free, their thickness is eight mils and they are 11 inches long. Their size is medium, and they come in a pack of 50 to be used in clinics and other settings.

Ideal for cutting soft or hard copper, brass, or aluminum tube used in HVAC/R applications.

Vibration absorbers are designed for installation in the suction and discharge lines of air conditioning, heat pump and refrigeration systems to dampen the transmission of compressor induced vibration through the system piping.

Features/Benefits

100 % helium and hydrogen leak tested
Compatible with all refrigerants
Deep pitch stainless steel hose and high tensile wire braid
Unique proven design for high pressure applications rated for R410A

Vibration absorbers are designed for installation in the suction and discharge lines of air conditioning, heat pump and refrigeration systems to dampen the transmission of compressor induced vibration through the system piping.

Features/Benefits

100 % helium and hydrogen leak tested
Compatible with all refrigerants
Deep pitch stainless steel hose and high tensile wire braid
Unique proven design for high pressure applications rated for R410A

CU CC SCRL 0.8HP 208-230/1/60 MED
Ambient Temp : 95 °F
Suction Temp : 25 °F
Voltage : 208-230/1/60
Application Capacity* : 8,980 BTU/H
Refrigerant Type : R404A
AWEF Value : 7.6

The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.

Arched top, concave sidewalls and rounded corners provide uniform tensile loading and uniform pulley sidewall contact for excellent belt service life and reduced pulley wear.

Vulcanized Flex-bonded tensile cords provide superior resistance to tensile and flexing forces, fatigue and shock loads.

Flex-Weave™ oil and heat resistant cover protects the belt core from the toughest environments.

All sizes meet Gates V80™ system matching tolerances.

Meets ARPM/RMA IP-3-2 oil and heat resistant standards and IP-3-3 static conductivity requirements. REACH and RoHS 2 compliant.

This heavy-duty, all-metal cutter is for CPVC, PVC and rubber tubing.

The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.

Arched top, concave sidewalls and rounded corners provide uniform tensile loading and uniform pulley sidewall contact for excellent belt service life and reduced pulley wear.

Vulcanized Flex-bonded tensile cords provide superior resistance to tensile and flexing forces, fatigue and shock loads.

Flex-Weave™ oil and heat resistant cover protects the belt core from the toughest environments.

All sizes meet Gates V80™ system matching tolerances.

Meets ARPM/RMA IP-3-2 oil and heat resistant standards and IP-3-3 static conductivity requirements. REACH and RoHS 2 compliant.

Vibration absorbers are designed for installation in the suction and discharge lines of air conditioning, heat pump and refrigeration systems to dampen the transmission of compressor induced vibration through the system piping.

Features/Benefits

100 % helium and hydrogen leak tested
Compatible with all refrigerants
Deep pitch stainless steel hose and high tensile wire braid
Unique proven design for high pressure applications rated for R410A

The P70 and P170 Controls for high pressure applications are designed primarily for high pressure cut-out control, head-pressure control, and condenser fan cycling control on commercial refrigeration and air conditioning applications.

The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.

Arched top, concave sidewalls and rounded corners provide uniform tensile loading and uniform pulley sidewall contact for excellent belt service life and reduced pulley wear.

Vulcanized Flex-bonded tensile cords provide superior resistance to tensile and flexing forces, fatigue and shock loads.

Flex-Weave™ oil and heat resistant cover protects the belt core from the toughest environments.

All sizes meet Gates V80™ system matching tolerances.

Meets ARPM/RMA IP-3-2 oil and heat resistant standards and IP-3-3 static conductivity requirements. REACH and RoHS 2 compliant.

The Robertshaw® line of replacement gas dials for gas valves come in many colors with various options.

Features and Benefits

Replacement dial for use with Unitrol® 7000 gas valves
Beige color with O

The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.

Arched top, concave sidewalls and rounded corners provide uniform tensile loading and uniform pulley sidewall contact for excellent belt service life and reduced pulley wear.

Vulcanized Flex-bonded tensile cords provide superior resistance to tensile and flexing forces, fatigue and shock loads.

Flex-Weave™ oil and heat resistant cover protects the belt core from the toughest environments.

All sizes meet Gates V80™ system matching tolerances.

Meets ARPM/RMA IP-3-2 oil and heat resistant standards and IP-3-3 static conductivity requirements. REACH and RoHS 2 compliant.

Piston service kit (NC); (5) O-rings, Al. gasket, piston assembly, insert block, piston ring, compression spring, refrigeration gasket

NRV V2 - Check Valves
NRV V2 one-piece check valves are used in liquid suction and hot gas lines in refrigeration and air conditioning applications. NRV valves ensure
the correct low direction and prevent back-condensation from a warm part of the system to the cold evaporator. The hermetic design of
solder version meets environmental demands for today and the future. The built-in damping piston makes the valves suitable for installation in
lines where pulsation can occur, e.g., in a compressor discharge line.

GBC V2 - Ball Valves
Danfoss GBC ball valves are manually operated shut-off valves suitable for bi-directional low. The design, weld, and choice of the sealing
material enable these ball valves to meet the most demanding requirements and provide years of leak-free performance.

This Fahrenheit scale thermometer comes with a 1" (25.4 mm) dial, a 5" (127 mm) stainless-steel probe and a pocket clip.

CU CC SCRL 2.0HP 208-230/1/60 MED
Ambient Temp : 95 °F
Suction Temp : 25 °F
Voltage : 208-230/1/60
Application Capacity* : 16,410 BTU/H
Refrigerant Type : R448A
AWEF Value : 7.6"

The 10-681 flame sensor is identical to Carrier/BDP part number LH33WZ511. The 10-681 is used in a system with the 41-409 hot surface ignitor.

Specifications

Replaces LH33WZ511

The Robertshaw 1970 Series Thermocouple Uni-Couple® design allows for installation to virtually all pilot burners. The versatile zip nut may be pushed, pulled or threaded onto the thermocouple's rolled threads for proper positioning in every application.

Features and Benefits

Easy burner installation with attached threaded nut
Stainless steel outer jacket for long life and resistance to heat blistering
Combination of copper and nickel alloys for good electrical conductivity
Mica washer to insulate from shorting conditions
Tinnerman clip included
Various lengths available for multiple applications

The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.

Arched top, concave sidewalls and rounded corners provide uniform tensile loading and uniform pulley sidewall contact for excellent belt service life and reduced pulley wear.

Vulcanized Flex-bonded tensile cords provide superior resistance to tensile and flexing forces, fatigue and shock loads.

Flex-Weave™ oil and heat resistant cover protects the belt core from the toughest environments.

All sizes meet Gates V80™ system matching tolerances.

Meets ARPM/RMA IP-3-2 oil and heat resistant standards and IP-3-3 static conductivity requirements. REACH and RoHS 2 compliant.