¾" x 3" Tube, expanded to ¾" ID on one side, ¼" Male Flare w/ Cap Wrench & Core

Features/Benefits

¼" SAE Male Flare
Brass cap with Neoprene O-ring
Stainless steel valve core, suitable for all refrigerants

Connector with two, ¼" male flares, one with core and cap in a 'U' shape. At the side is a ¼" female flare with depressor tip, and opposite that is an additional ¼" male flare.

Features/Benefits

¼" female flare with depressor tip on side and opposite is an additional ¼" male flare
Two ¼" male flares, one with core and cap, in a U shape

COUPLER, BRS

1-1/4 in piece of 1/4 in copper tubing
Double flared on one end with 1/4 in female flare nut and depressor tip
End of female flare swaged to allow 1/4 in copper tube to enter
Made of CDA 360 brass

COUPLER, BRS, MA FLARE X ACME FEM SWIVEL

Depressor tip and seal
Made of CDA 360 brass
Application Use to Make Connection Between with Unlike Threads
Nominal Size 1/4 in Male Flare x 1/2 in Acme Female Swivel
Connector Type Male Flare x Acme Female Swivel

START, HARD, 170 TO 277V, 1/3 TO 2 HP

Backup electronic timing circuit to protect the compressor
Can be used on PSC and CSIR type compressors
Easy 2-wire installation
Electronic potential relay (EPR) technology, Instant re-start, voltage sensing
NATE recognized (course #1867-0002)

START, HARD, 170 TO 277V, 1/2 TO 3 HP

Backup electronic timing circuit to protect the compressor
Can be used on PSC and CSIR type compressors
Easy 2-wire installation
Electronic potential relay (EPR) technology, Instant re-start, voltage sensing
NATE recognized (course #1867-0002)

COUPLER GAS RETAINING, 1/4″ FF X 1/4″ MPT
Adapter Fittings


RETAINING, CPLR, GAS, BRS, HVAC/R
Nominal Size 1/4 in MPT x 1/4 in Female Knurled Swivel

The valve body is stationary. When threads of the existing system fittings are stripped, and a new core will not go in, you can use SF8725.

Features/Benefits

Has a core and no depressor tip
Use when threads of existing system fittings are stripped and a new core wont go in
Valve body is stationary

This flare-sizing gauge is for R-410A systems.

Dramatically reduces the time to make flares and has a tool used with a cordless drill for the fastest flaring.

This tight-quarters universal flaring tool is adjustable to hold 3/16 to 5/8in (4.75 to 16mm) O.D. tubing. It automatically burnishes flare faces during operation with its unique faceted flaring cone.

The P70 and P170 Controls for low pressure applications are designed primarily for low pressure cut-out control, pump-down control, and capacity control on commercial refrigeration and air conditioning applications.

The P70 and P170 Controls for high pressure applications are designed primarily for high pressure cut-out control, head-pressure control, and condenser fan cycling control on commercial refrigeration and air conditioning applications.

The P70 and P170 Controls for high pressure applications are designed primarily for high pressure cut-out control, head-pressure control, and condenser fan cycling control on commercial refrigeration and air conditioning applications.

This vapor filter sensing tip works with LS1 and LS2 electronic leak detectors.

HEAT BLOCKING GEL
Viper Heat Blocking Gel is used to prevent fire or heat damage when using an open flame around wood, drywall, fabric and other components. It can also be used as a heat dissipating gel when protecting sensitive components in low temperature soldering applications. For high temperature brazing, soldering or welding we recommend our Viper Heat Blocking Putty.

Prevents Fires
Protects Sensitive Components
Wipes off easily
Non-Toxic and No Odors

¼" Male Flare X ¼" Female Flare Knurled Swivel w/ Depressor Tip & seal

Features/Benefits

¼" Female Knurled Swivel
¼" SAE Male Flare
Depressor Tip and Seal

FLAME-RESISTANT PAD
Viper WetRag® Heatshield is a revolutionary flame-resistant welding pad designed to prevent fires and protect sensitive components from heat transfer damage. Made from high temperature fire resistant absorbent carbon with a woven core of fiberglass, this versatile HeatShield can be used wet or dry and protects wood, insulation, studs, walls, flooring, valves, painted surfaces, metal, pipe, and other components or surfaces from damage. WetRag® HeatShield is machine washable and safe to dry.

High Temperature Resistant to 2500°F
Protects from Fires and Heat Transfer Damage
Can be used Wet or Dry
Reusable and Machine Washable

⅛" FPT X ¼" Female Flare Knurled Swivel w/ Depressor Tip & seal

Features/Benefits

¼" Female Knurled Swivel
⅛" FPT
Depressor Tip and Seal

The Robertshaw® 1900 Series Thermocouples include either a special low-mass or quick dropout thermocouple. It is usually found on applications that require an oxygen depletion system on the thermo safety. It is also found on many LP gas applications that require a quick dropout of the thermo safety if there is a loss of pilot flame. The Robertshaw 1980 Series Snap-Fit® Thermocouples offer easy installation into the majority of pilot burners. They are manufactured without complicated adaptors, but with extra insulation that the brass sheath provides under high ambient temperatures.

Features and Benefits
Easy burner installation with attached threaded nut
Stainless steel outer jacket for long life and resistance to heat blistering
Combination of copper and nickel alloys for good electrical conductivity
Mica washer to insulate from shorting conditions
Tinnerman clip included
Various lengths available for multiple applications

Pro-Series Programmable Touchscreen Wall Thermostat
Contractors can offer owners easy, yet powerful and reliable multi-stage temperature control in a simple, modern design with the Robertshaw RS9423T Programmable Touchscreen Wall Thermostat. The RS9423T is a Multi-Stage thermostat with 4 Heat / 2 Cool, Dual Fuel Compatibility and IAQ features.

• Compatible with Wireless Outdoor Temperature Sensor (RS9055OUT) for Duel Fuel balance point applications
• Large terminal blocks for easy installation
• Universal sub-base
• Quick-access menu button
• Contractor/technician setup menu
• Easy-to-understand programming menus
• Intuitive wake, leave, return, sleep programming icons
• 24V AC Powered OR Battery Operation (Included)
• 6 Year Limited Warranty
• Factory pre-set energy efficiency program
• Large, easy-to-read 8.8-square-inch blue backlit touchscreen display
• Easy access front load battery compartment
• Adjustable temperature differential (swing) for energy optimization and maximum system life
• Adjustable room temperature calibration
• Adjustable setpoint limits
• Five-minute selectable on/off compressor delay protection for short-cycling prevention
• Filter change reminder (selectable on/off)
• Keypad lockout

Combines the SPM-100 and the PRB-KIT and includes a brass gas fitting.

Line Service Valve 3/16" Copper Tubing, Wrench Cap and Core

Features/Benefits

3/16" Copper Tubing
Made of CDA 360 brass
Wrench Cap and Core

Hermetically designed moisture indicator with 3% relative humidity sensitivity, intended for use on refrigerant lines.

Features/Benefits

3% relative humidity indication compared to 10% paper indicators
3% relative humidity sensitivity
Accurate color calibration at low ppm levels and higher temperatures
All brass corrosion resistant body
Fully hermetic design
Maximum working pressure: 680 psig
Single indicator for all common refrigerants
Solid copper fittings
Tri color coded: Blue/Purple/Pink
Wide angle viewing/ high visibility window for ease of monitoring

Line service valve 5/16" copper tubing, wrench cap and core

Features/Benefits

5/16" Copper Tubing
Made of CDA 360 brass
Wrench Cap and Core

Hermetically designed moisture indicator with 3% relative humidity sensitivity, intended for use on refrigerant lines.

Features/Benefits

3% relative humidity indication compared to 10% paper indicators
3% relative humidity sensitivity
Accurate color calibration at low ppm levels and higher temperatures
All brass corrosion resistant body
Fully hermetic design
Maximum working pressure: 680 psig
Single indicator for all common refrigerants
Solid copper fittings
Tri color coded: Blue/Purple/Pink
Wide angle viewing/ high visibility window for ease of monitoring

Line service valve 1/8" copper tubing, wrench cap and core

Features/Benefits

⅛" Copper Tubing
Made of CDA 360 brass
Wrench Cap and Core

Measurement Range:
-40 to +80°F/-40 to +27°C
NSF® Certified
For Refrigerator/Freezer
Target range indication
Polycarbonate case
Non-mercuric column
Temperature guide on thermometer
2-way mounting: stand/hang