The J10 Series Humidistats and Dehumidistats are designed to regulate the relative humidity of confined spaces by cycling humidifying or dehumidifying equipment. Designed for central systems, the J10 controls are made from high impact plastic with a brushed finish dial plate. The J10's nylon sensing element provides long life and accurate humidity control. The J10-821 humidistat can be wall mounted or installed directly in a cold air return duct.

Features and Benefits

Strong plastic frame with integral switch eliminates the need to ground the control
Improved woven nylon sensing element provides a faster response time
Greater stability in set points over dramatic changes in relative humidity
Improved differential allowing 5% relative humidity

CAPACITOR, START, 400 – 480 MFD, 110V

Type two, dry, electrolytic, non-polarized, types for intermittent duty in AC motors and compressors, standard dual blade terminals
Industry standard case sizes
Made at Supco in Nanchang. Jiangxi, China
Moisture and oil resistant molded phenolic resin or plastic material
Non-PCB biodegradable synthetic oil, used where starting torques must be higher in relation to running torques
Application Motors and Compressors
Outside Diameter 1-13/16 in

This DOT-approved 50lb (22.68kg) recovery tank features a 1/4in SAE male fitting, a maximum pressure rating of 400psig and a water capacity of 47.7lbs (21.7kg).

CPS HP5A Offers
This premium refrigerant charge hose is leak-proof 8-sided crimp superior hose construction with "double barrier protection".

Features

All-weather flexibility and strength
Adjustable valve core depressor opens all out of tolerance Schraeder® valves
Blow-off grooves channel refrigerant to prevent spray back
Available with MicroSeal™ or ball valve fittings
1/4in SAE fittings with 45° bend on one end

This DOT-approved 50lb (22.68kg) recovery tank features a 1/4in SAE male fitting, a maximum pressure rating of 400psig and a water capacity of 47.7lbs (21.7kg).

This sight glass tool slides easily into the notches of a scroll compressor sight glass, and easily helps to extract the sight glass with a crescent or socket wrench. 1” diameter.

Features/Benefits

Extension slides into outer slots on 1 inch diameter sight glasses
Made of heavy-duty carbon steel
Once inserted use wrench or socket to remove the threaded sight glass

T-20/25 Tubing, 3/8" x 20FT

SWITCH, 1/4 IN, 6VDC, 12VDC, 36VDC, 18 AWG

1/4 in SAE 45 deg female flare fitting with valve core depressor
Automatic reset, high pressure switch opens on pressure rise
Life at rated load 100000 cycles
Small size and light weight for direct mounting, snap acting stainless steel hermetically sealed sensor, wire is 18 AWG, 18 in long
Frequency Rating 50/60 Hz
Nominal Size 1/4 in

SWITCH, PRES, 1/4 IN, 6VDC, 12VDC, 18 AWG

1/4 in SAE 45 deg female flare fitting with valve core depressor
Automatic reset, high pressure switch opens on pressure rise
Life at rated load 100000 cycles
Small size and light weight for direct mounting, snap acting stainless steel hermetically sealed sensor, wire is 18 AWG, 18 in long
Frequency Rating 50/60 Hz
Nominal Size 1/4 in

SWITCH, PRES, 1/4 IN, 12VDC, 36VDC, 18 AWG

1/4 in SAE 45 deg female flare fitting with valve core depressor
Automatic reset, high pressure switch opens on pressure rise
Life at rated load 100000 cycles
Small size and light weight for direct mounting, snap acting stainless steel hermetically sealed sensor, wire is 18 AWG, 18 in long
Frequency Rating 50/60 Hz
Nominal Size 1/4 in