GASKET & THREAD SEALANT
Nylog Blue is an elastic fluid made from synthetic refrigeration grade compressor oil. Nylog Blue is fully miscible and compatible with all system refrigerants and oils. Gaskets coated with Nylog will never dry or become heat fixed to the surface. Threaded connections coated with Nylog will block high pressure leaks by forming a hydraulic seal. Nylog can be used an assembly lube when installing shaft seals, o-rings, schraeder valves, ball valves, or other internal system components.

VCMA-15ULS Condensate Removal Pump, 1/50 hp, 115 V, 60 Hz, 6' cord, 65 gph @ 1 ft, with Safety Switch. The VCMA-15 Series with a 1/50 hp condensate pump is great for collecting, detecting, and removing condensation from air conditioners.

Seal kit (NC/NO); O-ring for armature tube, rubber gasket, support ring

VCMA-20UL-PRO Condensate Removal Pump, 1/30 hp, 115 V, 60 Hz, 6' cord, 84 gph @ 1 ft. VCMA-20-PRO Series effectively delivers high-efficiency condensate removal from air conditioners, gas furnaces, and condensing boilers.

GASKET AND THREAD SEALANT
Nylog White is a non-hardening and non-drying sealant used to prevent high pressure leaks on threaded connections, gaskets, PEX, and o-rings. Using the newest and most advanced pipe dope sealant technology based on a custom blend of silicones and Teflon, this product is designed for use on compressed air, water, gas, steam, and glycol systems.

GASKET & THREAD SEALANT
Nylog Red is an elastic fluid made from synthetic refrigeration grade compressor oil. Nylog Red is fully miscible and compatible with mineral oil refrigerants and oils. Gaskets coated with Nylog will never dry or become heat fixed to the surface. Threaded connections coated with Nylog will block high pressure leaks by forming a hydraulic seal. Nylog can be used an assembly lube when installing shaft seals, o-rings, schraeder valves, ball valves, or other internal system components.

The Robertshaw® 1960 Series Thermocouple is a special low-mass or quick dropout thermocouple. It is usually found on applications that require an oxygen depletion system on the thermo safety. It is also found on many LP gas applications that require a quick dropout of the thermo safety if there is a loss of pilot flame.

ATTENTION: The 1960-027 has standard thermocouple threads, and WILL NOT fit applications with metric threads.

Features and Benefits

Easy burner installation with attached threaded nut
Stainless steel outer jacket for long life and resistance to heat blistering
Combination of copper and nickel alloys for good electrical conductivity
Mica washer to insulate from shorting conditions
Tinnerman clip included
Various lengths available for multiple applications

The P70 and P170 Controls for high pressure applications are designed primarily for high pressure cut-out control, head-pressure control, and condenser fan cycling control on commercial refrigeration and air conditioning applications.

The P70 and P170 Controls for high pressure applications are designed primarily for high pressure cut-out control, head-pressure control, and condenser fan cycling control on commercial refrigeration and air conditioning applications.

The P70 and P170 Controls for high pressure applications are designed primarily for high pressure cut-out control, head-pressure control, and condenser fan cycling control on commercial refrigeration and air conditioning applications.

The P70 and P170 Controls for high pressure applications are designed primarily for high pressure cut-out control, head-pressure control, and condenser fan cycling control on commercial refrigeration and air conditioning applications.

The P70 and P170 Controls for high pressure applications are designed primarily for high pressure cut-out control, head-pressure control, and condenser fan cycling control on commercial refrigeration and air conditioning applications.

The P70 and P170 Controls for high pressure applications are designed primarily for high pressure cut-out control, head-pressure control, and condenser fan cycling control on commercial refrigeration and air conditioning applications.

The Ranco® O Series Single Low Pressure Controls offer a variety of pressure ranges and switch action to provide maximum application flexibility.

Features and Benefits

Controls available for most refrigerant types
High-amp rated switch (SPST) design (O10-1402/O10-1483)
Super Cap® capillary vibration protection system
Non-conductive front cover with captive screw
Adjustable differential and range
Easy-to-read scale plate
Vibration cone (absorbs and reduces vibration away from brazed joint)
Low mass copper alloy capillary tube (reduces capillary stress caused by equipment vibration)
The O16-624 control has additional features:

Compatible with refrigerants 134A, 401A, 401B, 402A, 402B, 403A, 403B and 404A
Cap included on all Australia temperature controls. Optional for all other regions

• Dedicated Open-Top Tool Storage Section for quick and easy access to tools
• Closed-Top Meter/Tester Storage Section w/ V-SWAP™ panel
• Waterproof Polypropylene plastic base for moisture and abrasion protection
• 1 Tape Loop
• 27 Total Exterior and Interior pockets
• 1 Stainless Tape Clip
• “Hang-up” hook
• Tarpaulin covered rear pocket for added weather and abrasion protection
• Detachable over-molded elastomeric grip handle
• YKK® zippers
• V-SWAP™ removable tool pocket panel system
• 5-Year Limited Warranty

Vinyl Rng 12-10 10 Stud (10 EA)

Fin whisk brush

Features/Benefits

Long lasting, sturdy Bristle Design

SSN2533--Silicon Nitride Ignitor replaces Heil Quaker (ICP) 1172533

This Igniter is used on many ArcoAire®, Comfortmaker®, Heil®, Tempstar®, and Whirlpool® furnaces.

PULLER, FILTER, 18 IN L EXTENDED

18 in Extension
Ergonomic Handle
Magnetic Tip

Supco® terminal service packs are handy and low priced, ideal for small jobs.

Features/Benefits

12-8 AWG ¼" (.250") Compressor Terminal 10 Pieces

The VCMA-15UL is ideal for automatic collection and removal of condensate from air conditioning, refrigeration and de-humidification equipment when gravity drainage is not possible or practical.

The HT-VCL-30P 115 Volt high-temperature condensate removal pump with 1-gallon collection tank is designed for plenum applications with the capability to handle the most difficult commercial applications.

The HT-VCL-30P 115 Volt high-temperature condensate removal pump with 1-gallon collection tank is designed for plenum applications with the capability to handle the most difficult commercial applications.

Q Series Sequencer, field proven for controlling the operation of heating elements and/or blower motors in electric, gas or oil heat systems. This sequencer has 2 switches & turns on at 30-90 seconds, and off at 1-30 seconds.

Features/Benefits

24 volt control circuit
Five second delay between all subsequent stages, unless they function together
UL® and CSA® approved

Off: 1 - 30 Seconds
On: 30 - 90 Seconds

Q Series Sequencer, field proven for controlling the operation of heating elements and/or blower motors in electric, gas or oil heat systems. This sequencer has 1 switch & turns on at 1-20 seconds, and off at 40-110 seconds.

Features/Benefits

24 volt control circuit
Five second delay between all subsequent stages, unless they function together
UL® and CSA® approved

Off: 40 - 110 Seconds
On: 1 - 20 Seconds

Q Series Sequencer, field proven for controlling the operation of heating elements and/or blower motors in electric, gas or oil heat systems. This sequencer has switches & turns on at 1-110 seconds, and off at 1-110 seconds.

Features/Benefits

24 volt control circuit
Five second delay between all subsequent stages, unless they function together
UL® and CSA® approved

Timing: Contacts M1-M2 will turn on 1st and turn off last
Off: 1 - 110 Seconds
On: 1 - 110 Seconds

Designed by a real technician in the field, this high-powered magnetic compressor cooler uses garden hose water to quickly cool overheated compressors for a hands-free, no mess solution.

Features/Benefits

Creates a Powerful Cascade of Water
Hands Free - Saves Time
High Powered Magnet and Garden Hose
No Messy Backsplash

Q Series Sequencer, field proven for controlling the operation of heating elements and/or blower motors in electric, gas or oil heat systems. This sequencer has 1 switch & turns on at 30-90 seconds, and off at 1-30 seconds.

Features/Benefits

24 volt control circuit
Five second delay between all subsequent stages, unless they function together
UL® and CSA® approved

Off: 1 - 30 Seconds
ON: 30 - 90 Seconds