CU CC SCRL 2.0HP 208-230/3/60 MED
Ambient Temp : 95 °F
Suction Temp : 25 °F
Voltage : 208-230/3/60
Application Capacity* : 20,700 BTU/H
Refrigerant Type : R404A
AWEF Value : 7.6

The Robertshaw® 1820 Series Pilot Uni-Kit® models are designed to replace hard-to-find ITT-General PG9 type pilots. A special 1/4” tubing adaptor is typically provided with nut and ball sleeve. Uni-Kits are available with and without a 32” (810mm) thermopile.

Features and Benefits

Many flame pattern types available
Thermocouple or thermopile options
Spark electrode available
Horizontal or vertical gas inlet
Several mounting bracket types available
Aerated pilots with non-linting characteristics

Evaporator Fan Universal Motor Kit 120 Volt 3000 RPM, Single Speed CW -clockwise rotation OR CCW-counter clockwise rotation. Replaces over 450 different evaporator motor types, Break off 2" Motor Shaft with Breakaways at 1/2" and 1-1/2".

Features/Benefits

Break off 2" motor shaft with breakaways at ½" and 1 ½"
CSA® Approved
Impedance protected
Includes all mounting accessories and hardware
Prefastened multi fit, break off mounting bracket
Replaces over 450 different evaporator type motors
Reversible rotation
Shaft diameter ⅛"
Single speed
UL® Recognized

Fan cycling low pressure switches

Features/Benefits

¼" SAE 45° female flare fitting with valve core depressor
Condenser fan cycling switch closes on pressure rise
Automatic Reset
Life at rated load: 100,000 cycles
Rated Voltage 24/120/240 VAC @ 50/60 Hz
Small size and light weight for direct mounting
Snap acting stainless steel hermetically sealed sensor
Wire is 18 AWG, 18" long

This molecular transformator sub-cooler provides valuable assistance in the transformation of high-temperature, pressure vapor refrigerant into low-temperature, pressure liquid refrigerant, dramatically improving recovery speed and efficiency.

¼" Male Flare, 5/16" ODS, ⅜" ODF w/ Cap Wrench & Core

Features/Benefits

¼" SAE Male Flare
Brass cap with Neoprene O-ring
Stainless steel valve core, suitable for all refrigerants

Evaporator Fan Universal Motor Kit 220 Volt 3000 RPM, Single Speed CW -clockwise rotation OR CCW-counter clockwise rotation. Replaces over 450 different evaporator motor types, Break off 2" Motor Shaft with Breakaways at 1/2" and 1-1/2".

Features/Benefits

Break off 2" motor shaft with breakaways at ½" and 1 ½"
CSA® Approved
Impedance protected
Includes all mounting accessories and hardware
Prefastened multi fit, break off mounting bracket
Replaces over 450 different evaporator type motors
Reversible rotation
Shaft diameter ⅛"
Single speed
UL® Recognized

Product Features
Synthetic ester lubricant provides excellent lubricity and compressor protection
Includes additive to prevent acid formation and corrosion
Includes O-ring conditioner, anti-wear & anti-oxidant additives
Compatible with PAG and mineral oils
Compatible with R134a and R12 refrigerant
100 cSt viscosity

Model HVAC Port-A-Torch® kit without cylinders contains all the quality equipment needed for brazing, and welding using oxygen and acetylene gases all in a convenient portable carrying case. The kit can braze up to 1 in. (25.4mm) diameter copper tube and is supplied with a size tip for brazing copper up to ½ in. (12.7mm) tube. The kit is capable of welding up to 1/8 in. (3.18mm) and is supplied with a tip that welds up to 1/16 in. (1.6mm) plate.

Features
Light Duty Port-A-Torch® V-Series threaded kit with cylinders designed to be used with oxygen and acetylene gases.
Regulator oxygen and acetylene model 601 with 50mm dual scale plastic gauges, notched adjusting knob and our distinguished internal encapsulated seat filter. Oxygen regulator that delivers up 80 psi and acetylene that regulator delivers up 15 psi.
Torch handle model 15-5HV solid brass torch handle is lightweight with front valves
Consumables included: mixer model 15HV and welding/brazing tip model 5090-1 & 3
Accessories included: Shade 5 safety glasses (ANSI Z87.1 CE Weld), Handheld ignitor, 3/16 in. x 12 ft. AxA twin R-grade hose, No. 5 chrome acetylene cylinder wrench, and black plastic PAT hose reel case.

SWITCH, PRES, 1/4 IN, 6VDC, 36VDC, 18 AWG

1/4 in SAE 45 deg female flare fitting with valve core depressor
Automatic reset, high pressure switch opens on pressure rise
Life at rated load 100000 cycles
Small size and light weight for direct mounting, snap acting stainless steel hermetically sealed sensor, wire is 18 AWG, 18 in long
Frequency Rating 50/60 Hz
Nominal Size 1/4 in

UC C LV AIR 2F 115 1PH M STD S 1
Evap. Temp : 25 °F
Voltage : 115/1/60
Room Temp :
Application Capacity* : 11,600 BTU/H
Refrigerant Type : R448A
Cooler AWEF > 32 : 9
Freezer AWEF <= 32 : N/A

Universal line valves, two styles - a flared or straight end copper piece

Features/Benefits

Copper Tee with the body Brazed on.
Flared Ends

These straight ball valve hose adapters feature 1/4in SAE Male x 1/4in SAE Female connections and come in a pack of 3.

CONTACTOR, 24V, 30A, 1.5, 40A, #10-32 SCREWS

Economically priced
Interchangeable mounting with many competitive contactors
Silver cadmium oxide contacts
Space saving dimensions allow for smaller panels and more wiring room
Application Low drop out voltage making them ideal for any air conditioning heating and refrigeration application

Quick coupler valve depressors complete with neoprene seal and depressor tips

Features/Benefits

1/4" Female Flare Swivel x ¼" Male Flare Access, 90° Configuration
Depressor Tip and Seal, No Valve Core
Made of CDA 360 brass

CU CC SCRL 2.0HP 208-230/3/60 LOW
Ambient Temp : 95 °F
Suction Temp : -10 °F
Voltage : 208-230/3/60
Application Capacity* : 9,310 BTU/H
Refrigerant Type : R404A
AWEF Value : 3.09

SWITCH, PRES, 1/4 IN, 6VDC, 12VDC, 36VDC

1/4 in SAE 45 deg female flare fitting with valve core depressor
Automatic reset, high pressure switch opens on pressure rise
Life at rated load 100000 cycles
Small size and light weight for direct mounting, snap acting stainless steel hermetically sealed sensor, wire is 18 AWG, 18 in long
Frequency Rating 50/60 Hz
Nominal Size 1/4 in

Pro-Series Programmable Touchscreen Wall Thermostat
Contractors can offer owners easy, yet powerful and reliable multi-stage temperature control in a simple, modern design with the Robertshaw RS9423T Programmable Touchscreen Wall Thermostat. The RS9423T is a Multi-Stage thermostat with 4 Heat / 2 Cool, Dual Fuel Compatibility and IAQ features.

• Compatible with Wireless Outdoor Temperature Sensor (RS9055OUT) for Duel Fuel balance point applications
• Large terminal blocks for easy installation
• Universal sub-base
• Quick-access menu button
• Contractor/technician setup menu
• Easy-to-understand programming menus
• Intuitive wake, leave, return, sleep programming icons
• 24V AC Powered OR Battery Operation (Included)
• 6 Year Limited Warranty
• Factory pre-set energy efficiency program
• Large, easy-to-read 8.8-square-inch blue backlit touchscreen display
• Easy access front load battery compartment
• Adjustable temperature differential (swing) for energy optimization and maximum system life
• Adjustable room temperature calibration
• Adjustable setpoint limits
• Five-minute selectable on/off compressor delay protection for short-cycling prevention
• Filter change reminder (selectable on/off)
• Keypad lockout

DCL/DCB/DAS/DCR - Filter Driers
Danfoss lter driers function as simple drop-in replacements for most driers sold in the aftermarket or installed on equipment by
manufacturers. All Danfoss lter driers are constructed with a solid core design to maximize moisture removal while minimizing pressure
drop. These driers use a mixture of molecular sieve and activated alumina to both adsorb system moisture and capture acid and prevent
solid contaminants from entering the system. The Danfoss 1.5 cubic inch hermetic lter drier can be used in hydrocarbon systems to provide
exceptional protection while minimizing charge requirements.

CONTACTOR, 3 PL, BX LUG, 65A, 120V, 50A

Economically priced
Interchangeable mounting with many competitive contactors
Silver cadmium oxide contacts
Space saving dimensions allow for smaller panels and more wiring room
Low Drop Out Voltage Making them Ideal for Any Air Conditioning Heating and Refrigeration

Model 5090 is a one-piece acetylene tip for welding/brazing torches. This tip is manufactured using environmentally-friendly tellurium copper that has excellent machining properties resulting in a higher quality tip. It is precision drilled and swaged for more precise and consistent flames. Model 5090 uses a universal separable tip tube and mixer system for sizes 0-10, eliminating the expense of using a different mixer for every tip size. The tip has a metal-to-metal contact seat virtually eliminating the possibility of leaks and the need for thread sealants. Conveniently vacuum-packed for point-of-purchase display.

Features
Constructed of tellurium copper
Welding and brazing tip for use with acetylene
Metal-to-metal seat virtually eliminates leaks
Precision drilled and swaged for more precise and consistent flames
Excellent machining properties yields a higher quality tip
Uses Harris universal mixer sizes 0-10
Marked with Harris logo and tip size for easy identification
One year warranty
Conveniently packaged for point-of-purchase display

For commercial and domestic refrigeration equipment, room and hood ventilators, evaporative coolers and various other equipment.

Features/Benefits

50/60Hz
Cast aluminum housing up to 16 watts
Hardware included
Overload protected
Permanent lubrication
Rotation determined by viewing opposite shaft end
Single rotation
Single speed, 1550 RPM
Sleeve bearings
Threaded mounting holes
Totally enclosed
UL® Approved
Universal mounting

The Robertshaw® Carbide Series Hot Surface Ignitors deliver dependable ignition in heating systems of every description: furnaces, boilers, rooftop heaters, infrared burners, unit heaters, water heaters, and many other types of HVAC equipment.

Features and Benefits

Made from high-purity recrystallized silicon carbide. (Crystar™) which combines physical and thermal strength with stable electrical properties
Designed to reach ignition temperature(s) within 17 seconds
Have 18-gauge nickel chrome lead wires embedded and metalized in place for maximum holding strength and electrical conductivity
Manufactured with lead wires enclosed in a special high-temperature fiberglass insulation providing electrical protection
Operate at 120V AC. Some modules are rated for 208/240V input, however, the voltage to the ignitor is stepped down to 120V AC

Product Features
Thermal insulation tape protects Metal Pipes, Tubing And Fittings against Heat, Water, and Air.
Self adhesive and easy to apply.
Stops sweating and condensation on cold lines.
Insulates against heat loss on hot lines.
Wrap around expansion valve to protect it from heat in the engine compartment.
Excellent for sound deadening applications.

DCL/DCB/DAS/DCR - Filter Driers
Danfoss lter driers function as simple drop-in replacements for most driers sold in the aftermarket or installed on equipment by
manufacturers. All Danfoss lter driers are constructed with a solid core design to maximize moisture removal while minimizing pressure
drop. These driers use a mixture of molecular sieve and activated alumina to both adsorb system moisture and capture acid and prevent
solid contaminants from entering the system. The Danfoss 1.5 cubic inch hermetic lter drier can be used in hydrocarbon systems to provide
exceptional protection while minimizing charge requirements.

Features:

Attacks Corrosion: Frees bolts, fasteners and other mechanical components
Removes Rust and Carbon Deposits: Will not attack or damage metal
Penetrates Faster: Penetrates quicker and deeper than similar products
Works Everywhere: Use on any corroded threads or tight parts
Simplifies Repairs: Makes the toughest maintenance jobs easier, faster and safer to execute.
Penetrates Deeper: Penetrates the smallest spaces, threads and openings
Details:

Loosen frozen metal parts the professional way, with Kroil original penetrant in liquid and aerosol (formerly Aero Kroil) formulas. Discover why this is the best penetrating oil to loosen bolts in various applications. When it comes to freeing corroded items in tough spaces, nothing rivals powerful, industry-proven Kroil penetrating oil. Used and trusted by pros and experienced DIYers alike since 1939, Kroil quickly loosens rusted nuts and bolts, frees frozen shafts, pulleys, and more. No space is too tight to reach, thanks to Kroil's ability to penetrate the smallest opening, thread or crevice. Corrosion meets its match, as Kroil removes and prevents rust, cleans and lubricates, and displaces moisture.

CU CC SCRL 3.0HP 208-230/3/60 LOW
Ambient Temp : 95 °F
Suction Temp : -10 °F
Voltage : 208-230/3/60
Application Capacity* : 13,200 BTU/H
Refrigerant Type : R404A
AWEF Value : 3.15

UC C LP EL 4F 230 1PH M STD S 1
Evap. Temp : -20 °F Low Temp
Voltage : 208-230/1/60