The SLS series of 1/2" bimetal temperature controls offers proven reliability in a compact, versatile, cost-effective design.

Features/Benefits

Auto reset
CSA approved
Offered in a broad temperature range to cover most heating applications
UL® recognized

Terminals: 45° angle ¼"
Cut out temp ( °F): 170 °F
Cut in temp ( °F): 130 °F
Differential °: 40 °F

CAPACITOR, RUN, OVAL DUAL, 25+5 MFD, 440V

10,000 AFC pressure sensitive short circuit interrupting capability
Continuous life tested, oil leak tested and dielectric tested for insulation effectiveness
Life tested to 85°C operating temperature for 10,000 cycles
Manufactured with thick polypropylene foil to handle increased operating temperatures, PCB-free oil to prevent over-heating
Meets EIA-456A accelerated life test at 70°C for 60,000 hours
US and Canada UL Approved (C22.2NO.190)

SUPCO® flame sensors can replace many of the popular sensors in today's furnaces that use hot surface or direct spark ignition systems.

Features/Benefits

Alumina ceramic insulator
For Hot Surface Ignition (HSI) systems
Kanthal flame rod material can withstand 1800°F
Mount on multiple burners, or adjacent to igniter
Use with spark ignition and flame sensing

Length (Flange to Tip): 4"
Termination: .25" Quick Disconnect

The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.

Arched top, concave sidewalls and rounded corners provide uniform tensile loading and uniform pulley sidewall contact for excellent belt service life and reduced pulley wear.

Vulcanized Flex-bonded tensile cords provide superior resistance to tensile and flexing forces, fatigue and shock loads.

Flex-Weave™ oil and heat resistant cover protects the belt core from the toughest environments.

All sizes meet Gates V80™ system matching tolerances.

Meets ARPM/RMA IP-3-2 oil and heat resistant standards and IP-3-3 static conductivity requirements. REACH and RoHS 2 compliant.

CAPACITOR, OVLD, RLY, 110 TO 125VAC, 115V

Designed for modern high efficiency compressors, easy mount clip for quick installation
For systems with or without run capacitors
Helps older compressors start and run cooler
Prevents low voltage starting problems
Wire designations - white/start, black/common, red/run

Supco® terminal service packs are handy and low priced, ideal for small jobs.

Features/Benefits

12-8 AWG ¼" (.250") Compressor Terminal 10 Pieces

Supco® terminal service packs are handy and low priced, ideal for small jobs.

Features/Benefits

16-14 AWG #10 stud 13/64" I.D. 100 Pieces

CONTACTOR, 3 PL, BX LUG ,90A, 24V, 75A

Economically priced
Interchangeable mounting with many competitive contactors
Silver cadmium oxide contacts
Space saving dimensions allow for smaller panels and more wiring room
Low Drop Out Voltage Making them Ideal for Any Air Conditioning Heating and Refrigeration

These black Mechanix Wear FastFit MFF-05 mechanics gloves are size XX-large and are made with tricot, synthetic leather, and TrekDry. In addition, they have nylon stitching, and have a keystone thumb style. They are rated ANSI/ISEA Puncture Level 1. They are full-finger, have a shirred slip-on cuff, and an EN 388 Rating of 2121X. They feature pull straps, reinforced thumb crotch, and touchscreen compatibility.

CAPACITOR, RUN, OVAL, 50 MFD, 440V

10,000 AFC pressure sensitive short circuit interrupting capability
Continuous life tested, oil leak tested and dielectric tested for insulation effectiveness
Life tested to 85°C operating temperature for 10,000 cycles
Manufactured with thick polypropylene foil to handle increased operating temperatures, PCB-free oil to prevent over-heating
Meets EIA-456A accelerated life test at 70°C for 60,000 hours
US and Canada UL Approved (C22.2NO.190)

CONTACTOR, 2 PL, 10-32 SCREWS, 30A, 24V, 20A

Economically priced
Interchangeable mounting with many competitive contactors
Silver cadmium oxide contacts
Space saving dimensions allow for smaller panels and more wiring room

CAPACITOR,START,216 – 259 MFD,220V

Type two, dry, electrolytic, non-polarized, types for intermittent duty in AC motors and compressors, standard dual blade terminals
Industry standard case sizes
Made at Supco in Nanchang. Jiangxi, China
Moisture and oil resistant molded phenolic resin or plastic material
Non-PCB biodegradable synthetic oil, used where starting torques must be higher in relation to running torques
Application Motors and Compressors
Outside Diameter 2-1/16 in

PULLER, BLADE, FAN, STEEL

5/8 in steel center shaft
4 pull fingers
Alignment tool included
Fine thread version provides additional torque and pulling power
Sturdy, heavy duty steel, Has flats for wrench

The Ranco® O Series Single Low Pressure Controls offer a variety of pressure ranges and switch action to provide maximum application flexibility.

Features and Benefits

Controls available for most refrigerant types
High-amp rated switch (SPST) design (O10-1402/O10-1483)
Super Cap® capillary vibration protection system
Non-conductive front cover with captive screw
Adjustable differential and range
Easy-to-read scale plate
Vibration cone (absorbs and reduces vibration away from brazed joint)
Low mass copper alloy capillary tube (reduces capillary stress caused by equipment vibration)
The O16-624 control has additional features:

Compatible with refrigerants 134A, 401A, 401B, 402A, 402B, 403A, 403B and 404A
Cap included on all Australia temperature controls. Optional for all other regions

• Glows Under Black Light, Enhancing Visibility
• High Viscosity Gas Leak Detection Fluid
• Clings To Vertical Surfaces, Freeze Proof to 0°F (-17.77°C)
• Fast, Accurate Detection Of The Smallest Leaks
• Convenient Dauber Type Applicator Cap
• Tiny leaks result in large bubbles and faster, larger
leaks are indicated by a stream of bubbles

CAPACITOR, RUN, OVAL, 80 MFD, 440V

10,000 AFC pressure sensitive short circuit interrupting capability
Continuous life tested, oil leak tested and dielectric tested for insulation effectiveness
Life tested to 85°C operating temperature for 10,000 cycles
Manufactured with thick polypropylene foil to handle increased operating temperatures, PCB-free oil to prevent over-heating
Meets EIA-456A accelerated life test at 70°C for 60,000 hours
Ul Standard US and Canada UL Approved (C22.2NO.190)

CONTACTOR, 3 PL, BX LUG, 120A, 120V, 90A

Complete competitive cross-reference available
Economically priced
Interchangeable mounting with many competitive contactors
Silver cadmium oxide contacts
Space saving dimensions allow for smaller panels and more wiring room
Low Drop Out Voltage Making them Ideal for Any Air Conditioning Heating and Refrigeration

Connector with two, ¼" male flares, one with core and cap in a 'U' shape. At the side is a ¼" female flare with depressor tip, and opposite that is an additional ¼" male flare.

Features/Benefits

¼" female flare with depressor tip on side and opposite is an additional ¼" male flare
Two ¼" male flares, one with core and cap, in a U shape

This replacement sensor works with LS1 and LS2 electronic leak detectors.

Differential Manometer grouped together with T Fittings, Static Tips, Tubing and a carrying case.

Features

Dual input with ±120" H2O range
0.001" H2O maximum resolution
Seven units of measure (mbar, kPa, PSI, mmHg, inHg, mmH2O, inH2O)
Display – 4 digit with backlight
Smooth – Stabilizes display when measuring fluctuating pressures

Robertshaw® offers direct replacements for several leading OEM brand ignitors. These ignitors are constructed with sturdy, long-lasting silicon nitride for maximum longevity. The Robertshaw 41-426N is a 120V Direct Replacement for Carrier LH33ZG001 with a 8.27 inch wire length and 1.5 inch insulator.

The ETC-200-E Pressure Transducer is a high-accuracy, durable sensor for HVAC and refrigeration systems. Compatible with CPC, Emerson, Copeland, and Danfoss systems including RMCC, E2, E2e, E3, AK-SC255, AK-SC355, AK-SM800, and AK-SM800a. Equivalent to Danfoss 060G3990 and CPC part number 800-2200.

Note: supplied with 2M Cable

The ETC-1122 Green Discharge Temperature Sensor is designed for accurate temperature measurement and control, offering high reliability and precision. Equivalent to Emerson / Copeland / CPC part numbers 501-1121 & 501-1122 and Parker, Micro Thermo Technologies™ part number 023-0073..

Use this hose to transfer and/or charge refrigerants. Its length provides long, convenient reach for your applications.

BUSTER, RUST

Countertop display case
Flexible spout extends and retracts to any in-between length
Loosens rust in seconds
No lingering odor

CAPACITOR, RUN, OVAL, 12.5 MFD, 440V

10,000 AFC pressure sensitive short circuit interrupting capability
Continuous life tested, oil leak tested and dielectric tested for insulation effectiveness
Life tested to 85°C operating temperature for 10,000 cycles
Manufactured with thick polypropylene foil to handle increased operating temperatures, PCB-free oil to prevent over-heating
Meets EIA-456A accelerated life test at 70°C for 60,000 hours
US and Canada UL Approved (C22.2NO.190)